[1] Han JC, Dutta S, Ekkad S (2012) Gas turbine heat transfer and cooling technology. CRC Press Taylor & Francis Group, Florida.
[2] Mick WJ, Mayle RE (1988) Stagnation film cooling and heat transfer, including its effect within the hole pattern, ASME J Turbomach 110(1): 66-72.
[3] Ekkad SV, Han JC, Du H (1998) Detailed film cooling measurement on a cylindrical leading edge model: effect of free-streamturbul ence and coolant density. ASME J Turbomach 120: 799-807.
[4] Rozati A, Tafti DK (2008) Large Eddy simulation of leading edge film cooling-Part II: Heat transfer and effect of blowing ratio. ASME J Turbomac 130(4): 041015-1-7.
[5] Rozati A, Tafti DK (2008) Effect of coolant blowing ratio on leading edge film cooling flow and heat transfer-LES investigation. Int J Heat Fluid Flow 29: 857-873.
[6] Ou S, Rivir RB (2001) Leading edge film cooling heat transfer with high free stream turbulence using a transient liquid crystal image method. Int J Heat Fluid Flow 22(6): 614-623.
[7] Mehendale AB, Han JC (1992) Influence of high mainstream turbulence on leading edge film cooling heat transfer. ASME J Turbomach 114: 707-715.
[8] Mehendale AB, Han JC (1993) Reynolds number effect on leading edge film effectiveness and heat transfer coefficient. Int J Heat Mass Transfer 36: 3723-3730.
[9] Taslim M, Khanicheh A (2006) Experimental and numerical study of impingement on an airfoil leading edge with and without showerhead and gill film holes. ASME J Turbomach 128(2): 310-320.
[10] Cutbirth JM, Bogard DG (2003) Effects of coolant density ratio on film cooling performance on a vane. ASME Paper No. 2003 GT-38582.
[11] Karni J, Goldstein RJ (1990) Surface injection effect on mass transfer from a cylinder in crossflow: a simulation of film cooling in the leading edge region of a turbine blade. ASME J Turbomach 112: 418-427.
[12] Gao Z, Han J (2009) Influence of film-hole shape and angle on showerhead film cooling using PSP technique. ASME J Heat Transfer 131(6): 061701-061701-11.
[13] Li S, Yang S, Han J (2013) Effect of coolant density on leading edge showerhead film cooling using the pressure sensitive paint measurement technique. ASME J Turbomach 136(5): 051011-10.
[14] Reiss H, Bölcs A (2000) Experimental study of showerhead cooling on a cylinder comparing several configurations using cylindrical and shaped holes. ASME J Turbomach 122: 161-169.
[15] Tao Z, Yao Y (2020) Experimental and numerical study on film cooling effectiveness of an annular cascade endwall with different slot configuration. Int J Therm Sci
158: 106517
[16] Nathan M, Dyson T, Bogard D, Bradshaw S (2014) Adiabatic and overall effectiveness for the showerhead film cooling of a turbine vane. ASME J Turbomach 136(3): 031005-1-9.
[17] Han JC, Chowdhury HK, Qureshi A (2017) Influence of turbine blade leading edge shape on film cooling with cylindrical holes. Int J Heat Mass Tran 115: 895-908.
[18] Wang J, Lia L,
Li J,
Changh F (2020) Numerical investigation on flow and heat transfer characteristics of vortex cooling in actual film-cooled leading edge. Appl Therm Eng (2020):115942.
[19] Al-Zurfia N, Turanc A, Nasserc A (2019) A numerical study of anti-vortexfilm-coolingholes designs in a 1-1/2 turbine stage using LES. Propuls Power Res 8(4): 275-299
[20] حسینی سم، زیرک س، رجبی زرگرآبادی م (1398) بررسی عددی تاثیر تزریق هوای خنک کننده نوسانی سینوسی بر خنک کاری لایه ای لبه حمله، سطح فشار و مکش یک پره توربین. نشریه علمی مکانیک سازه‌ها و شاره‌ها 247-227 :(2)9.
[21] حسینعلی‌پور سم، شهبازیان ح، قبادی م، نوروزی م ص (1397) آنالیز سیالاتی-حرارتی اثرات دوران و بویانسی دورانی در خنک‌کاری داخلی پره‌های توربین گاز-مطالعه آزمایشگاهی. نشریه علمی مکانیک سازه‌ها و شاره‌ها 288-277 :(3)8.
[22] محمدی ا، صالحی س، رئیسی م (1399) کمی‌سازی عدم‌قطعیت جریان و انتقال حرارت مغشوش در خنک‌کاری لایه‌ای. نشریه علمی مکانیک سازه‌ها و شاره‌ها 192-177 :(2)10.
[23] York WD, Leylek JH (2003) Leading edge FilmCooling physics-Part III: Diffused hole effectiveness. ASME J Turbomach 125: 165-187.
[24] Beimaert-Chartrel G, Bogard DG (2012) CFD predictions of heat transfer coefficient augmentation on a simulated film cooled turbine blade leading edge. ASME Paper No. GT2012-70015.
[25] Rutledge JL, Polanka MD (2014) Computational fluid dynamics evaluations of unconventional film cooling scaling parameters on a simulated turbine blade leading edge. J Turbomach 136: 101006-15.
)