Investigation of the simultaneous effect of laser shock peening and graphene oxide coating on residual stress and fatigue corrosion properties of IN792 alloy

Authors

1 Ph.D. Student, Mech. Eng., University of birjand, birjand, Iran

2 Prof., Mech. Eng., University of birjand, birjand, Iran

3 Assoc. Prof., Materials Eng., Birjand University of Technology ., birjand, Iran

4 Assis. Prof., Departement of Physics., Vali-e-Asr University of Rafsanjan, Rafsanjan, Iran

Abstract

Laser shock peening is a mechanical surface treatment that is caused by laser beam radiation on the surface of the metal. This processing causes plastic deformation, and compressive residual stresses under the surface of metal. In addition, applying nanostructure coatings is one of the new methods to increase the resistance of components under corrosive environment and high temperature. The purpose of this article is to investigate laser shock peening on residual stress and fatigue corrosion of Inconel 792 in 75% Na_2 SO_4+15% NaCl+10% V_2 O_5 environment. For this purpose, a number of samples were subjected to laser shock peening and another group was coated with graphene oxide before laser processing. Then, all the samples were subjected to corrosive environment at high temperature, and then the fatigue test was performed. The result of this research showed that the laser shock peening operation increased the fatigue life of this alloy for 2.4 times.

Keywords

Main Subjects

References

[1] Brooks, C. R. (1982). Heat treatment, structure and properties of nonferrous alloys. (No Title).
[2] Sims, C. T., Stoloff, N. S., & Hagel, W. C. (Eds.). (1987). superalloys II (Vol. 8). New York: Wiley.
[3] Neidel, A., & Riesenbeck, S. (2012). Pitting Corrosion Induced Fatigue Fracture on a Gas Turbine Compressor Blade. Prakt. Metallogr., 49(1), 35-48.
[4] Schönbauer, B. M., Stanzl-Tschegg, S. E., Perlega, A., Salzman, R. N., Rieger, N. F., Zhou, S. & Gandy, D. (2014). Fatigue life estimation of pitted 12% Cr steam turbine blade steel in different environments and at different stress ratios. Int. J. Fatigue, 65, 33-43.
[5] Larrosa, N. O., Akid, R., & Ainsworth, R. A. (2018). Corrosion-fatigue: a review of damage tolerance models. Int. Mater. Rev., 63(5), 283-308.
[6] Lu, J. Z., Luo, K. Y., Yang, D. K., Cheng, X. N., Hu, J. L., Dai, F. Z., & Zhang, Y. K. (2012). Effects of laser peening on stress corrosion cracking (SCC) of ANSI 304 austenitic stainless steel. Corros. Sci., 60, 145-152.
[7] Rozmus-Górnikowska, M., Kusiński, J., & Cieniek, Ł. (2020). Effect of laser shock peening on the microstructure and properties of the inconel 625 surface layer.             J. Mater. Eng. Perform. 29, 1544-1549.
[8] Ding, K., & Ye, L. (2006). Laser shock peening: performance and process simulation. Woodhead Publishing.
[9] Zhang, C., Dong, Y., & Ye, C. (2021). Recent developments and novel applications of laser shock peening: a review. Adv. Eng. Mater., 23(7), 2001216.
[10] Maleki, E., Unal, O., Guagliano, M., & Bagherifard, S. (2021). The effects of shot peening, laser shock peening and ultrasonic nanocrystal surface modification on the fatigue strength of Inconel 718. Mater. Sci. Eng.: A, 810, 141029.
[11] Bai, Y. C., Hua, Y. Q., Rong, Z., Xue, Q., & Chen, R. F. (2014). On laser shock processing to improve hot corrosion resistance of In718 superalloy.        Adv. Mater. Res, 989, 27-30.
[12] Prabhakaran, S., Kumar, H. P., Kalainathan, S., Vasudevan, V. K., Shukla, P., & Lin, D. (2019). Laser shock peening modified surface texturing, microstructure and mechanical properties of graphene dispersion strengthened aluminium nanocomposites. Surf. Interfaces, 14, 127-137.
[13] Karthik, D., & Swaroop, S. (2017). Laser shock peening enhanced corrosion properties in a nickel based Inconel 600 superalloy. Journal of Alloys and Compounds, 694, 1309-1319.
[14] Wang, C., Shen, X. J., An, Z. B., Zhou, L. C., & Chai, Y. (2016). Effects of laser shock processing on microstructure and mechanical properties of K403 nickel-alloy. Mater. Des. 89, 582-588.
[15] Bae, S., Kim, Y., Jung, J., Shin, K., Suh, C. M., & Jeong, S. (2024). Effects of laser shock peening on Inconel 738LC to improve mechanical and fatigue characteristics.               Opt. Laser Technol., 171, 110290.
[16] Cockings, H. L., Cockings, B. J., Harrison, W., Dowd, M., Perkins, K. M., Whittaker, M. T. & Gibson, G. J. (2020). The effect of near-surface plastic deformation on the hot corrosion and high temperature corrosion-fatigue response of a nickel-based superalloy. J. Alloys Compd. 832, 154889.
[17] Sun, Y., Wu, H., Du, H., & Yao, Z. (2022). Investigation of Strain Fatigue Behavior for Inconel 625 with Laser Shock Peening. Materials. 15(20), 7269.
[18] Morar, N. I., Holtham, N., Hackel, L., Davami, K., Sharma, M., DeWald, A., & Roy, R. (2023). Effects of high-energy laser peening followed by pre-hot corrosion on stress relaxation, microhardness, and fatigue life and strength of single-crystal nickel CMSX-4® superalloy. Int. J. Adv. Des. Manuf. Technol. 126(11), 4893-4912.
[19] Ding, R., Li, W., Wang, X., Gui, T., Li, B., Han, P., & Song, L. (2018). A brief review of corrosion protective films and coatings based on graphene and graphene oxide. J. Alloys and Compounds, 764, 1039-1055.
[20] Yi, Z., Kangning, C., Wei, W., Wang, J., & Lee, S. (2007). Effect of IrO2 loading on RuO2–IrO2–TiO2 anodes: A study of microstructure and working life for the chlorine evolution reaction.             Ceram.Int. 33(6), 1087-1091.
[21] Yadav, V. S., Sankar, M. R., & Pandey, L. M. (2020). Coating of bioactive glass on magnesium alloys to improve its degradation behavior: Interfacial aspects. J. Magnesium Alloys, 8(4), 999-1015.
[22] Telang, A., Gill, A. S., Teysseyre, S., Mannava, S. R., Qian, D., & Vasudevan, V. K. (2015). Effects of laser shock peening on SCC behavior of Alloy 600 in tetrathionate solution. Corros. Sci. 90, 434-444.
[23] TELANG, A., GILL, A. S., RAMAKRISHNAN, G., & VASUDEVAN, V. K. (2018). Effect of Different Ablative Overlays on Residual Stresses Introduced in IN718 SPF by Laser Shock Peening. Int. J. Peening Sci. Tech. (IJPST).
[24] Pradhan, D., Mahobia, G. S., Chattopadhyay, K., & Singh, V. (2018). Effect of pre hot corrosion on high cycle fatigue behavior of the superalloy IN718 at 600 C. Int. J. Fatigue. 114, 120-129.
[25] Rozmus-Górnikowska, M., Kusiński, J., & Cieniek, Ł. (2020). Effect of laser shock peening on the microstructure and properties of the inconel 625 surface layer.             J. Mater. Eng. Perform. 29, 1544-1549.
[26] Bae, S., Kim, Y., Jung, J., Shin, K., Suh, C. M., & Jeong, S. (2024). Effects of laser shock peening on Inconel 738LC to improve mechanical and fatigue characteristics.               Opt. Laser Technol. 171, 110290.
[27] Hfaiedh, N., Peyre, P., Song, H., Popa, I., Ji, V., & Vignal, V. (2015). Finite element analysis of laser shock peening of 2050-T8 aluminum alloy. Int. J. Fatigue 70, 480-489.
[28] Finegan, D. P., Vamvakeros, A., Cao, L., Tan, C., Heenan, T. M., Daemi, S. R., & Ban, C. (2019). Spatially resolving lithiation in silicon–graphite composite electrodes via in situ high-energy x-ray diffraction computed tomography.   Nano Lett. 19(6), 3811-3820.
[29] Nath, S., Shukla, P., Shen, X., & Lawrence, J. (2018). Effect of laser shock peening (LSP) on the phase evolution, residual stress and hardness of Hastelloy-X superalloys.              Lasers Eng. 39(1-2), 97-112.
[30] Huang, S., Liu, J., Sheng, J., Meng, X., Hu, X., Zhu, M., Zhou, J. (2022). High-temperature fatigue crack growth characteristics of IN718 Ni-based alloy treated by laser peening. Eng. Fract. Mech. 276, 108922.
[31] Kaufman, J., Špirit, Z., Vasudevan, V. K., Steiner, M. A., Mannava, S. R., Brajer, J., & Mocek, T. (2021). Effect of laser shock peening parameters on residual stresses and corrosion fatigue of AA5083. Metals, 11(10), 1635.
[32] Hilly, M. E. (1971). Residual stress measurement by X-ray diffraction. SAE Information Report, 784.
 [33] Ross, J. R. (2018). Contemporary Catalysis: Fundamentals and Current Applications. Elsevier.
[34] Wang, L., Yu, K., Cheng, X., Cao, T., & Zhou, L. (2023). Effect of laser shock peening on microstructure and mechanical properties of laser cladding 30CrMnSiNi2A high-strength steel. Scientific Reports, 13(1), 9971.
[35] Samuel, C., Moganraj, A., Swaroop, S., Praveenkumar, K., Natarajan, A., Nageshwara Rao, M., & Bhattacharya, B. (2023). Effect of laser shock peening without coating on grain size and residual stress distribution in a microalloyed steel grade. Crystals, 13(2), 212.
[36] Mahobia, G. S., Paulose, N., Mannan, S. L., Sudhakar, R. G., Chattopadhyay, K., Srinivas, N. S., & Singh, V. (2014). Effect of hot corrosion on low cycle fatigue behavior of superalloy IN718. Int. J. Fatigue. 59, 272-281.
[37] Bae, S., Kim, Y., Jung, J., Shin, K., Suh, C. M., & Jeong, S. (2024). Effects of laser shock peening on Inconel 738LC to improve mechanical and fatigue characteristics.               Opt. Laser Technol. 171, 110290.
[38] Mahobia, G. S., Paulose, N., Mannan, S. L., Sudhakar, R. G., Chattopadhyay, K., Srinivas, N. S., & Singh, V. (2014). Effect of hot corrosion on low cycle fatigue behavior of superalloy IN718. Int. J. Fatigue. 59, 272-281.
[39] Huang, S., Liu, J., Sheng, J., Meng, X., Hu, X., Zhu, M & Zhou, J. (2022). High-temperature fatigue crack growth characteristics of IN718 Ni-based alloy treated by laser peening. Eng. Fract. Mech. 276, 108922.
[40] Mączka, M., Collings, I. E., Leite, F. F., & Paraguassu, W. (2019). Raman and single-crystal X-ray diffraction evidence of pressure-induced phase transitions in a perovskite-like framework of [(C 3 H 7) 4 N][Mn (N (CN) 2) 3]. Dalton Transactions, 48(25), 9072-9078.
[41] Kashaev, N., Ushmaev, D., Ventzke, V., Klusemann, B., & Fomin, F. (2020). On the application of laser shock peening for retardation of surface fatigue cracks in laser beam‐welded AA6056. Fatigue Fract. Eng. Mater. Struct. 43(7), 1500-1513.
 
[42] Geethapriyan, T., Palani, I. A., Singh, M. K., Rai, D. K., Shanmuga Priyan, V. G., & Subbu, S. K. (2023). Post-processing of wire arc additive manufactured stainless steel 308L to enhance compression and corrosion behavior using laser shock peening process. J. Mater. Eng. Perform. 1-15.
[43] Yoo, Y. R., Choi, S. H., & Kim, Y. S. (2023). Effect of laser peening on the corrosion properties of 304L stainless steel. Materials, 16(2), 804.
Journal of Solid and Fluid Mechanics
Volume 14, Issue 5
November and December 2024
Pages 121-136

Files

Share

How to cite

Statistics