Investigating the effect of induced centrifugal force resulting from duct geometry on the propagation speed of premixed flame using OpenFOAM software

Authors

1 Department of Mechanic and Aerospace, Malek -Ashtar University of Technology, Isfahan, Iran

2 Member of the Faculty of Malek- Ashtar University of Technology

Abstract

Increasing the propagation speed of the flame due to centrifugal force can lead to reducing the length of the combustion chamber and increasing the thrust-to-weight ratio in air gas turbine engines. The effect of centrifugal force on the propagation of the premixed flame has been investigated. For this purpose, the large eddy simulation of premixed combustion of the air-propane mixture in two straight and curved ducts with a step in the outer wall as a flame holder was performed using OpenFoam software and compared with the experimental data. The ducts have an inlet and outlet, and the averaged temperature and the wrinkling (the ratio of laminar to turbulent flame speed) were investigated for two different inlet velocities. It was observed that the curved duct inducing centrifugal force to the fuel and air mixture causes better mixing and wrinkling, increases the area of the flame, and as a result, the speed of flame propagation was improved. Also, the curved duct can withstand increasing the inlet velocity to higher values. To study the effect of fluid circulation, a new duct geometry for more mixture circulation was designed and analyzed. The comparison of temperature and wrinkling parameters in the outlet section for two initial curve ducts (C2) and the new one (C3) showed that the increase in the rotation due to the increase in centrifugal force improved the average temperature and wrinkling parameters in the outlet.

Keywords

References

[1] Ramaprabhu P, Andrews MJ (2004) Experimental Investigation of Rayleigh-Taylor Mixing at Small Atwood Numbers. J. Fluid Mech 502: 233-271. 
[2] Lewis GD, Shadowen JH, Thayer EB (1977) Swirling Flow Combustion. J. Energy 1(4): 201-205.
[3] Lewis GD (1973) Centrifugal-force Effects on Combustion. Proc. Combust. Inst: 413-419.
[4] Lewis GD (1971) Combustion of a Centrifugal-force Field. Proc. Combust. Inst: 625-629.
[5] Lapsa A, Dahm WJA (2007) Experimental Study on the Effects of Large Centrifugal Forces on Step-Stabilized Flames. 5th US Combustion Meeting 75.
[6] Lapsa A, Dahm WJA (2009) Hyperacceleration Effects on Turbulent Combustion in Premixed Step-Stabilized Flames. Proc. Combust. Inst: 1731-1738.
[7] Sykes JP, Gallagher TP, Rankin BA (2020) Effects of Rayleigh-Taylor instabilities on turbulent premixed flames in a curved rectangular duct. Proc. Combust. Inst: 1-8.
[8] Katta VR, Blunck D, Roquemore WM (2013) Effect of Centrifugal Effects on the Flame Stability in an Ultra-Compact Combustor. AIAA-1046.
[9] Briones AM, Sekar B, Erdmann TJ (2015) Effect of Centrifugal Force on Turbulent Premixed Flames. J. Eng. Gas Turbines Power 137(1): 11501-11511.
[10] Moshir SGH, Mostofizadeh A, Bazazzadeh M (2022) Investigation of the Effect of Centrifugal Acceleration on the Flame Propagation Speed in Premixed Combustion. Fuel and combustion scientific research journal 14(4): 100-122. (In Persian).
[11] Bohan BT ,Polanka MD (2019) A New Spin on Small-Scale Combustor Geometry. J. Eng. Gas Turbines Power 141(1): 11504-11514.
[12] Wilson JD, Damele CJ , Polanka MD (2014) Flame Structure Effects at High G-Loading. J. Eng. Gas Turbines Power 136(10): 101502-101510.
[13] Rathsack TC, Bohan BT, Polanka MD, Goss LP (2019) Experimental Investigation of Flow Characteristics in an Ultra Compact Combustor. AIAA, California.
[14] Thomas NR, Rumpfkeil MP, Briones AM (2019) Multiple-Objective Optimization of a Small-Scale, Cavity-Stabilized Combustor. AIAA, California.
[15] Zhao D, Gutmark EJ, Goey P (2018)  A review of cavity-based trapped vortex, ultra-compact, high-g, interturbine combustors. Prog. Energy. Combust. Sci 66: 42–82.
[16] Puranam SV, Arici J (2009) Turbulent combustion in a curving, contracting channel with a cavity stabilized flame. Proc. Combust. Inst 32: 2973-2981.
[17] Koopaei SE, Mazaheri K (2012) Numerical Investigation of the Effects of Blockage Ratio and Obstruction Geometry on Flame Acceleration and Overpressure of Gas Explosion. Fuel and Combustion.  5: 1-24. (in Persian)
[18] Hajialigol N, Mazaheri K (2016) Turbulent lean premixed flame response to the imposed inlet oscillating velocity and effect of the equivalence ratio and inlet temperature on it. Fuel and Combustion. 9: 21-37. (in Persian)
[19] Erdmann TJ, Gutmark E, Caswell AW (2023) The Effects of High Centrifugal Acceleration on Bluff-Body Stabilized Premixed Flames. J. Eng. Gas Turbines Power. 145: 31004-31015.
[20] Zhao Y, Fan W, Rongchun Zh (2023) Influence of coupling schemes of radial and circumferential flame stabilization modes on flow and combustion characteristics of compact combustion for gas turbine. Fuel 333.
[21] Pishbin SI, Ghazikhani M, Modarres Razavi SM (2015) Experimental Investigation on Low Swirl Premixed Combustion and Effects of Geometrical Parameters on Its Performance. J of Solid and Fluid Mechanics. 5: 191-204. (in Persian)
[22] Blazek J (2001) Computational Fluid Dynamics: Principles and Applications. Elsevier.
[23] Libby PA, Williams FA (1980) In Turbulent Reacting Flows, Topics in Applied Physics. Lecture Notes in Physics. Springer-Verlag.  44.
 
[24] Yoshizawa A, Horiuti K (1985) A Statistically-Derived Subgrid-Scale Kinetic Energy Model for the Large-Eddy Simulation of Turbulent Flows. J. Phys. Soc. Japan  54: 2834-2839.
[25] Weller HG (1993) The development of a new flame area combustion model using conditional averaging. Thermo-fluids section report TF/9307. Imperial College of Science. Technology and Medicine.
[26] Holzmann T (2019) Mathematics, Numerics, Derivations and OpenFOAM. First Edition.
Journal of Solid and Fluid Mechanics
Volume 13, Issue 1
March and April 2023
Pages 111-124

Files

Share

How to cite

Statistics