[1] Davoodi B, Eskandari B (2015) Investigation of tool life and wear mechanisms in turning of N-155 iron-nickel-base superalloy using response surface methodology. Modares Mechanical Engineering 14(15): 51-58. (In Persian)
[2] Debnath S, Reddy MM, Sok Yi Q (2014) Environmental friendly cutting fluids and cooling techniques in machining: A review. J Clean Prod 83: 33-47.
[3] Davoodi B, Musavi SH (2016) An experimental investigation of the effect of lubrication method on surface roughness and cutting fluid consumption in machining of super alloys. Modares Mechanical Engineering 16(10): 343-352. (in Persian)
[4] Shabgard MR, Jafarian Zenjanab M, Azarafza R (2014) Experimental study on the influence of CuO nanofluid on surface roughness and machining force in turning of AISI 4340 steel. Modares Mechanical Engineering 14(2): 27-33. (in Persian)
[5] Chetan Ghosh S, Rao PV (2015) Application of sustainable techniques in metal cutting for enhanced machinability: A review. J Clean Prod 100(1): 17-34.
[6] Cui X, Guo J (2017) Effects of cutting parameters on tool temperatures in intermittent turning with the formation of serrated chip considered. Appl Therm Eng 110: 1220-1229.
[7] Dogu Y, Aslan E, Camuscu N (2005) A numerical model to determine temperature distribution in orthogonal metal cutting. J Mater Process Technol 171(1): 1-9.
[8] Atlati S, Haddag B, Nouari M, Moufki A (2015) Effect of the local friction and contact nature on the Built-Up Edge formation process in machining ductile metals. Tribol Int 90: 217-227.
[9] Gomez-Parra A, Alvarez-Alco M, Salguero J, Batista M, Marcos M (2013) Analysis of the evolution of the built-up edge and built-up layer formation mechanisms in the dry turning of aeronautical aluminum alloys. Wear 302: 1209-1218.
[10] Kaynak Y, Karaca HE, Noebe RD, Jawahir IS (2013) Tool-wear analysis in cryogenic machining of NiTi shape memory alloys: A comparison of tool-wear performance with dry and MQL machining. Wear 306: 51-63.
[11] Dhananchezian M, Kumar MP (2011) Cryogenic turning of the Ti–6Al–4V alloy with modified cutting tool inserts. Cryogenics 51(1): 34-40.
[12] Dhar NR, Kamruzzaman M (2007) Cutting temperature, tool wear, surface roughness and dimensional deviation in turning AISI-4037 steel under cryogenic condition. Int J Mach Tools Manuf 47(5): 754-759.
[13] Krishnamurthy G, Bhowmick S, Altenhof W, Alpas AT (2016) Increasing efficiency of Ti-alloy machining by cryogenic cooling and using ethanol in MRF. CIRP J Manuf Sci Technol 408-422.
[14] Shokrani A, Dhokia V, Newman ST (2016) Investigation of the effects of cryogenic machining on surface integrity in CNC end milling of Ti–6Al–4V titanium alloy. J Manuf Processes 21: 172-179.
[15] Tazehkandi AH, Shabgard M, Pilehvarian F (2015) Application of liquid nitrogen and spray mode of biodegradable vegetable cutting fluid with compressed air in order to reduce cutting fluid consumption in turning Inconel 740. J Clean Prod 108(1): 90-103.
[16] Maruda RW, Krolczyk GM, Niesłony P, Krolczyk JB, Legutk S (2016) Chip formation zone analysis during the turning of austenitic stainless steel 316L under MQCL cooling condition. International Conference on Manufacturing Engineering and Materials, ICMEM 2016, Procedia Engineering 149: 297-304.
[17] Ulutan D, Ozel T (2011) Machining induced surface integrity in titanium and nickel alloys: A review. Int J Mach Tools Manuf 51(3): 250-280.
[18] Padmini R, Vamsi Krishna P, Krishna Mohana Rao G (2016) Effectiveness of vegetable oil based nanofluids as potential cutting fluids in turning AISI1040 steel. Tribol Int 94: 490-501.
[19] Sharma P, Singh Sidhu B, Sharma J (2015) Investigation of effects of nanofluids on turning of AISI D2 steel using minimum quantity lubrication. J Clean Prod 108: 72-79.
[20] Sayuti M, Ming Erh O, Sarhan AD, Hamdi M (2014) Investigation on the morphology of the machined surface in end milling of aerospace AL6061-T6 for novel uses of SiO2 nanolubrication system. J Clean Prod 66: 655-663.
)