Experimental and numerical simulation study of the performance of the polyphenylene sulfide thermoplastic composite reinforced with carbon fibers under high-velocity impact of projectiles with different geometries

Author

Head of the Department of Research and Industrial Centers, Imam Ali university, Tehran, Iran

10.22044/jsfm.2024.13692.3800

Abstract

Nowadays, thermoplastic composites have gained significant popularity in various industries due to their high strength-to-weight ratio. The aim of the current research is to investigate the ballistic performance of a four-layer thermoplastic composite under high-velocity impact. This composite utilizes polyphenylene sulfide as the matrix material and carbon fibers as the reinforcing phase. In this study, the composite was first fabricated with a symmetric layering configuration [0/90/90/0] using a hot press method, and its mechanical properties were determined through tensile testing. Subsequently, high-velocity impact tests were conducted on sample specimens, and the exit velocities of the projectiles were measured using a high-speed camera. Additionally, numerical simulations of these high-velocity impacts were performed using the finite element software LS-DYNA, and the results were compared and validated against experimental data. In these simulations, three different projectile geometries, namely, flat-nosed, conical, and spherical, were employed. Ultimately, based on the numerical and experimental outcomes, it was determined that the fabricated composite was capable of absorbing a significant amount of energy from the impacting projectiles. The highest energy absorption was observed at an initial velocity of 120 meters per second, corresponding to the flat-nosed projectile with a 65.67% absorption rate, while the lowest was associated with the conical projectile, with a 36.66% absorption rate.

Keywords

Main Subjects


  • Li, H., et al. (2014) Synthesis and characterization of novel poly (phenylene sulfide) containing a chromophore in the main chain. Polymer international. 63(9): p. 1707-1714.
  • Zhao, L., et al. (2019) High-performance polyphenylene sulfide composites with ultra-high content of glass fiber fabrics. Composites Part B: Engineering. 174: p. 106790.
  • Deng, J., et al. (2022) Thermal aging effects on the mechanical behavior of glass-fiber-reinforced polyphenylene sulfide composites. Polymers. 14(7): p. 1275.
  • Jiang, , et al. (2017) Rheological and mechanical properties of polyphenylene sulfide reinforced with round and rectangle cross-section glass fibers. High Performance Polymers, 29(7): p. 849-856.
  • Li, J., et al. (2019) Improving interfacial and mechanical properties of glass fabric/polyphenylene sulfide composites via grafting multi-walled carbon nanotubes. RSC advances. 9(56): p. 32634-32643.
  • Wu, Y., et al. (2019) Improved mechanical properties of graphene oxide/short carbon fiber–polyphenylene sulfide composites. Polymer Composites. 40(10): p. 3866-3876.
  • Reddy, P.R.S., et al., Effect of viscoelastic behaviour of glass laminates on their energy absorption subjected to high velocity impact. Materials & Design, 2016. 98: p. 272-279.
  • Liu, L., et al. (2018)An experimental investigation on high velocity impact behavior of hygrothermal aged CFRP composites. Composite Structures,. 204: p. 645-657.
  • Deka, L., S. Bartus, and U. Vaidya (2008) Damage evolution and energy absorption of E-glass/polypropylene laminates subjected to ballistic impact. J. mate. sci,. 43: p. 4399-4410.

[10] Heimbs, S., et al. (2014) High velocity impact on preloaded composite plates. Composite Structures, 111: p. 158-168.

[11] Ignatova, A., O. Kudryavtsev, and M. Zhikharev (2020) Influence of surface polymer coating on ballistic impact response of multi-layered fabric composites: Experimental and numerical study. International J. Impact Eng., 144: p. 103654.

[12] da Silva, A.A.X., et al. (2021) High-velocity impact behavior of aramid/S2-glass interply hybrid laminates. Applied Composite Materials, 28(6): p. 1899-1917.

[13] Delavari, K. and A. Safavi, The effect of stacking sequence on high-velocity impact resistance of hybrid woven reinforced composites: experimental study and numerical simulation. Fibers and Polymers, 2022: p. 1-12.

[14] Cantwell, W.J. and J. Morton (1991) The impact resistance of composite materials—a review. composites, 1991. 22(5): p. 347-362.

[15] Singh, N.K. and K. Singh (2015) Review on impact analysis of FRP composites validated by LS‐DYNA. Polymer Composites, 36(10): p. 1786-1798.

[16] Barauskas, R. and A. Abraitienė (2007) Computational analysis of impact of a bullet against the multilayer fabrics in LS-DYNA. Int. J. impact eng., 34(7): p. 1286-1305.

[17] Camanho, P.P., et al (2008) A numerical material model for predicting the high velocity impact behaviour of polymer composites. in Mechanical Response of Composites. Springer.

[18] Ansari, M.M. and A. Chakrabarti (2016) Impact behavior of FRP composite plate under low to hyper velocity impact. Composites Part B: Engineering, 95: p. 462-474.

[19] Yen, C.-F., et al. (2020) Modeling and simulation of carbon composite ballistic and blast behavior. J. Compo. Mate, 54(4): p. 485-499.

[20] Mousavi, M.V. and H. Khoramishad (2020) Investigation of energy absorption in hybridized fiber-reinforced polymer composites under high-velocity impact loading. Int. J. Imp. Eng, 146: p. 103692.

[21] Lee, R., (2019) LS-DYNA for Engineers: A Practical Tutorial Book.: BW Publications.

 

[22] Chang, F.-K. and K.-Y. Chang (1987) Post-failure analysis of bolted composite joints in tension or shear-out mode failure. J. Compo. Mate., 21(9): p. 809-833.

[23] Khodadadi, A., et al. (2019) Numerical and experimental study of impact on hyperelastic rubber panels. IRI. Poly. J., 28: p. 113-122.

[24] Asemani, S.S., et al. (2021) The experimental and numerical analysis of the ballistic performance of elastomer matrix Kevlar composites. Polymer Testing, 2021. 102: p. 107311.

[25] Haro, E.E., A.G. Odeshi, and J.A. Szpunar (2016) The energy absorption behavior of hybrid composite laminates containing nano-fillers under ballistic impact. Int. J. Imp. Eng., 96: p. 11-22.