<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE ArticleSet PUBLIC "-//NLM//DTD PubMed 2.7//EN" "https://dtd.nlm.nih.gov/ncbi/pubmed/in/PubMed.dtd">
<ArticleSet>
<Article>
<Journal>
				<PublisherName>دانشگاه صنعتی شاهرود</PublisherName>
				<JournalTitle>مکانیک سازه ها و شاره ها</JournalTitle>
				<Issn>2251-9475</Issn>
				<Volume>16</Volume>
				<Issue>4</Issue>
				<PubDate PubStatus="epublish">
					<Year>2026</Year>
					<Month>09</Month>
					<Day>23</Day>
				</PubDate>
			</Journal>
<ArticleTitle>Study of Aluminum Matrix Metal Composite Reinforced with SiC Particles Fabricated by Powder Metallurgy Method</ArticleTitle>
<VernacularTitle>مطالعه ساخت کامپوزیت فلزی زمینه آلومینیوم تقویت شده با ذرات SiC به روش متالورژی پودر</VernacularTitle>
			<FirstPage>445</FirstPage>
			<LastPage>453</LastPage>
			<ELocationID EIdType="pii">3993</ELocationID>
			
<ELocationID EIdType="doi">10.22044/jsfm.2026.17490.4047</ELocationID>
			
			<Language>FA</Language>
<AuthorList>
<Author>
					<FirstName>یاسر</FirstName>
					<LastName>نجفی راد</LastName>
<Affiliation>گروه مهندسی مکانیک، دانشکده مهندسی، دانشگاه صنعتی کرمانشاه، کرمانشاه، ایران</Affiliation>

</Author>
<Author>
					<FirstName>سجاد</FirstName>
					<LastName>رسایی</LastName>
<Affiliation>عضو هیات علمی/ دانشگاه صنعتی کرمانشاه</Affiliation>

</Author>
</AuthorList>
				<PublicationType>Journal Article</PublicationType>
			<History>
				<PubDate PubStatus="received">
					<Year>2026</Year>
					<Month>02</Month>
					<Day>14</Day>
				</PubDate>
			</History>
		<Abstract>In this study, an aluminum matrix composite reinforced with silicon carbide (SiC) particles was fabricated via the powder metallurgy route, and the effects of three key parameters namely reinforcement content (0, 0.5, 1, 2, and 4 wt.%), compaction pressure (9, 10, 11, 12, and 13 tons), and sintering temperature (470, 500, 550, and 600 °C) on the microstructure and tensile strength were systematically evaluated. The experimental design was established using the Taguchi method. The results revealed that increasing the SiC content up to an optimum level (approximately 1 wt.%) enhanced strength and reduced porosity; however, excessive SiC content (especially 4 wt.%) led to particle agglomeration and stress concentration, which promoted pore growth and significantly deteriorated the mechanical properties. Moreover, raising the sintering temperature within the studied range (from 470 to 600 °C) decreased the number of pores but increased their size, resulting in a higher overall porosity. The optimal combination of processing parameters (1 wt.% SiC, 11 tons compaction pressure, and 600 °C sintering temperature) yielded the best mechanical performance, exhibiting higher tensile strength (approximately 77 MPa) while maintaining acceptable ductility compared with other samples. Microstructural analyses confirmed that precise control of reinforcement fraction, compaction pressure, and sintering temperature is crucial for achieving high densification and a uniform microstructure.</Abstract>
			<OtherAbstract Language="FA">در این پژوهش، کامپوزیت‌های زمینه آلومینیوم تقویت‌شده با ذرات کاربید سیلیسیوم به‌روش متالورژی پودر تولید شد و اثر سه پارامتر کلیدی شامل درصد وزنی تقویت‌کننده (0، 0/5، 1، 2 و 4 درصد وزنی)، فشار فشرده‌سازی (9، 10، 11، 12 و 13 تن) و دمای زینترینگ (470، 500، 550 و 600 درجه سلسیوس) بر ریزساختار و استحکام کششی بررسی گردید. طراحی آزمایش‌ها بر اساس روش تاگوچی انجام شد. نتایج نشان داد که افزایش درصد تا مقدار بهینه (حدود 1 درصد وزنی) موجب بهبود استحکام و کاهش تخلخل می‌شود، اما افزایش بیش از حد آن (به ویژه 4 درصد وزنی) با ایجاد تمرکز تنش و تجمع ذرات، سبب رشد حفره‌ها و افت شدید خواص مکانیکی می‌گردد. همچنین افزایش دمای زینترینگ در محدوده بررسی‌شده (از 470 تا 600 درجه سلسیوس) باعث کاهش تعداد حفره‌ها ولی افزایش اندازه آنها و در نتیجه افزایش تخلخل کل شد. بهترین عملکرد مکانیکی مربوط به نمونه‌ای با ترکیب بهینه پارامترها (1 درصد وزنی ، فشار 11 تن و دمای 600 درجه سلسیوس) بود که استحکام کششی بالاتر (حدود 77 مگاپاسکال) و تغییر طول قابل‌قبول نسبت به سایر نمونه‌ها نشان داد. تحلیل ریزساختار تأیید کرد که کنترل همزمان درصد تقویت‌کننده، فشار تراکم و شرایط زینترینگ، نقش تعیین‌کننده‌ای در دستیابی به چگالی بالا و ساختار یکنواخت دارد.</OtherAbstract>
		<ObjectList>
			<Object Type="keyword">
			<Param Name="value">متالورژی پودر</Param>
			</Object>
			<Object Type="keyword">
			<Param Name="value">کامپوزیت فلزی</Param>
			</Object>
			<Object Type="keyword">
			<Param Name="value">آلومینیوم</Param>
			</Object>
			<Object Type="keyword">
			<Param Name="value">کاربید سیلیسیوم</Param>
			</Object>
		</ObjectList>
<ArchiveCopySource DocType="pdf">https://jsfm.shahroodut.ac.ir/article_3993_5434f00869b83130d39ead47e4a3a0e0.pdf</ArchiveCopySource>
</Article>
</ArticleSet>
