@article { author = {Cheloee Darabi, A. and Chamani, H.R. and Ayatollahi, M. R.}, title = {Predicting macromechanical behavior of dual phase steels based on actual micromechanical modeling}, journal = {Journal of Solid and Fluid Mechanics}, volume = {5}, number = {1}, pages = {31-38}, year = {2015}, publisher = {Shahrood University of Technology}, issn = {2251-9475}, eissn = {2251-9483}, doi = {10.22044/jsfm.2015.423}, abstract = {In this paper the macromechanical behavior of dual phase steel based on actual microstructure has been predicted. In order to prepare dual phase steelsc (DP) of different percent phase combinations, a low carbon steel (C-Mn) was subjected to intercritical annealing treatment (ICT) and quenched in water. Then, the actual microstructures of dual phase steels were obtained by metallographic analysis and optical microscopy. A 2D representative volume element (RVE) was generated by finite element code Ansys on the basis of actual microstructure which was obtained by image processing code in Matlab software. The individual single-phase flow curves were obtained based on the dislocation theory and the local chemical composition of constituent. The results of 2D micromechanical RVE models under periodic boundary conditions and tension loading were compared with the experimental results. It is shown that the 2D micromechanical model can predict both strength and ductility for low volume fraction of martensite in dual phase steels. The 2D micromechanical modeling may then be used to portray the local strain evolution of the individual phases in the DP microstructures.}, keywords = {Dual phase steel,micromechanical modeling,mechanical behavior,periodic boundary condition}, title_fa = {پیش‎بینی رفتار ماکرومکانیکی فولادهای دوفازی با استفاده از مدل‎سازی میکرومکانیکی ریزساختار واقعی}, abstract_fa = {در این مقاله رفتار ماکرومکانیکی فولادهای دوفازی با استفاده از مدل‌سازی میکرومکانیکی پیش‌بینی شده است. به منظور ساخت فولاد دوفازی با درصدهای مختلف فاز مارتنزیت، فولاد C-Mn تحت عملیات‌ حرارتی مختلف قرار گرفته و سپس در آب کوئنچ شده است. پس از آن با استفاده از متالوگرافی و تصویربرداری میکروسکوپ نوری، ریز ساختارهای واقعی فولادهای دوفازی بدست آمده‌ است. با استفاده از کد پردازش تصویر نوشته شده در نرم‌افزار Matlab ریز ساختار‌های واقعی پردازش شده و سپس با استفاده از کد اجزا محدود نوشته شده در نرم‌افزار Ansys، سلول واحد دو بعدی مدل شده است. در ادامه، با استفاده از تئوری نابجایی و ترکیب شیمیایی موضعی فازهای فریت و مارتنزیت، منحنی تنش-کرنش واقعی این فازها استخراج شده است. نتایج مدل‌سازی میکرومکانیکی دو بعدی سلول واحد با شرایط مرزی پریودیک تحت بارگذاری کشش تک محوره انجام شده با نتایج آزمایش تجربی مقایسه شده است. در این بررسی نشان داده می‌شود که مدل میکرومکانیکی دوبعدی در درصد فاز مارتنزیت‌های پایین قابلیت پیش‌بینی استحکام و رفتار نرم‌شوندگی فولادهای دوفازی را دارد. علاوه بر آن از مدل میکرومکانیکی دوبعدی به منظور ارزیابی پیشرفت موضعی شدن کرنش نیز می‌توان استفاده نمود.  }, keywords_fa = {فولاد دوفازی,مدل‌سازی میکرومکانیکی,رفتار مکانیکی,شرط مرزی پریودیک}, url = {https://jsfm.shahroodut.ac.ir/article_423.html}, eprint = {https://jsfm.shahroodut.ac.ir/article_423_547fd43dfe21683f4b1336b310193321.pdf} }