@article { author = {Alimohammadi, A. and Jalali Aghchai, Abdol. H.}, title = {Experimental and Numerical Study on forming limit diagram of two-layer metallic sheets at high temperature}, journal = {Journal of Solid and Fluid Mechanics}, volume = {10}, number = {1}, pages = {107-120}, year = {2020}, publisher = {Shahrood University of Technology}, issn = {2251-9475}, eissn = {2251-9483}, doi = {10.22044/jsfm.2020.8561.2945}, abstract = {Two-layer metallic sheets are very important Alternative for single-layer metal sheets which have many advantages including weight loss and high strength to weight ratio. Using these sheets saves energy. Hence, the replacement of single-layer metal sheets with two-layer metallic sheets is one of the industry's requirements. One of the most important defects in the sheet metal forming is tearing. Heating of the sheet is one of the ways to postpone the tearing. According to previous studies, there has been no research on warm formability of two-layer metallic sheets. In this research, the aim of the study is to determine forming limit diagram of copper-aluminum two-layer sheets at warm temperature range by experimental and numerical methods. In the experimental method, the formability diagram was obtained by Stretch forming tests with hemispherical punch and Tensile tests. The results of the experimental method showed that with increasing temperature, the formability increases, The maximum deformation force is reduced, also the height of the dome-shaped height increases with increasing temperature. On the other hand, the simulated model in Abaqus software has a fairly good fit with the experimental model. The best model for predicting precisely the necking momentum was the M-K model.}, keywords = {Formability,two-layer metallic sheets,forming limit diagram at high temperature,Stretch forming test}, title_fa = {مطالعه تجربی و عددی حد شکل‌دهی ورق دو‌لایه مس-آلومینیوم در دمای بالا}, abstract_fa = {ورق‌های دولایه فلزی جایگرین بسیار مهمی برای ورق‌های فلزی تک لایه هستند که دارای مزایای فراوانی از جمله کاهش وزن و نسبت استحکام به وزن بالا می‌باشند. استفاده از این ورق‌ها موجب صرفه‌جویی بالایی در انرژی می‌شود. از این رو جایگزینی ورق‌های فلزی با ورق‌های دولایه یکی از ضرورت‌های صنعت محسوب می‌شود. یکی از مهم‌ترین عیوب در شکل‌دهی ورق‌ها، پارگی است. یکی از راه‌های به تعویق انداختن پارگی، گرم کردن ورق می‌باشد. با توجه به مطالعات انجام‌شده تاکنون تحقیقی راجع به شکل‌پذیری در فرآیندهای گرم ورق دولایه انجام نشده است. در این پژوهش هدف بررسی حد شکل‌پذیری ورق‌های دولایه مس- آلومینیوم در محدودی دمایی گرمکاری به روش تجربی و عددی می‌باشد. در روش تجربی منحنی حد شکل‌پذیری با انجام آزمایش‌های اتساع با سنبه سرکروی و کشش تک محوری حاصل گردید. نتایج حاصل از روش تجربی نشان داد که با افزایش دما میزان شکل‌پذیری، افزایش می‌یابد، میزان ماکزیمم نیروی شکل‌پذیری کاهش و همچنین میزان ارتفاع حد گنبدی شکل با افزایش دما، افزایش می‌بابد. و از طرفی مدل شبیه سازی شده در نرم افزار آباکوس تطابق خوبی با مدل تجربی داشت که بهترین مدل برای پیش بینی دقیق لحظه گلویی شدن مدل M-K می باشد.}, keywords_fa = {شکل‌پذیری,ورق دولایه,منحنی حد شکل‌پذیری در دمای بالا,آزمایش اتساع}, url = {https://jsfm.shahroodut.ac.ir/article_1808.html}, eprint = {https://jsfm.shahroodut.ac.ir/article_1808_9ffb5bd76d46060b795395ed45e84daa.pdf} }