[1] Tlusty J, Polacek M (1963) The stability of machine tools against self excited vibrations in machining. Prod Engi Conf, Pittsburgh. 474-465.
[2] Tobias S, Fishwick A (1958) The chatter of lathe tools under orthogonal cutting conditions. Trans ASME (80): 1088-1079.
[3] Minis I, Yanushevsky T (1993) A new theoretical approach for the prediction of the machine tool chatter in milling. ASME J Eng Ind (115):1-8.
[4] Budak E, Altintas Y (1998) Analytical prediction of chatter stability in milling. ASME J Dyna Sys (120): 22-36.
[5] Kaneko T, Sato H, Tani Y, O-hori M (1984) Self-excited chatter and its marks in turning. Trans ASME (222): 228-106.
[6] Kurata Y, Doruk Merdol S, Altintas Y, Suzuki N, Shamoto E (2010) Chatter stability in turning and milling with in process identified process damping. J Adv Mech Des (4): 1107-1118.
[7] Ozlu E, Budak E (2007) Comparison of one dimensional and multi-dimensional model in stability analysis of turning operations. Int J Mach Tool & Manu (47): 1883-1875.
[8] Wu DW (1989) A new approach of formulating the transfer function for dynamic cutting process. J Eng Indu (111): 37-47.
[9] Altintas Y, Eynian M, Onozuka H (2008) Identification of dynamic cutting force coefficients and chatter stability with process damping. Manu Tech CIRP Ann (57): 371–374.
[10] Budak E, Tunc LT (2009) A new method for identification and modeling of process damping in machining. J Manuf Sci E-T ASME (131): 051019-1- 051019-10.
[11] Eynian M, Altintas Y (2009) Chatter stability of general turning operations with process damping. J Manuf Sci E-T ASME (131): 041005-1-041005-10.
[12] Ahmadi K, Ismail F (2010) Experimental investigation of process damping nonlinearity in machining chatter. Int J Mach Tools and Manu (50): 1006–1014
[13] Ahmadi K, Ismail F (2011) Analytical stability lobes including nonlinear process damping effect on machining chatter. Int J Mach Tools and Manu (51): 296-308.
[14] Wu, DW (1988) Application of a comprehensive dynamic cutting force model to orthogonal wave-enerating processes, Int J Mech Sci (30): 581-600.
[15] Chiou YS, Chung ES, Liang SY (1995) Analysis of tool wear effect on chatter stability in turning. Int J Mech Sci (37): 391–404.
[16] Zaghbani I, Songmene V (2009) Estimation of machine tool dynamic parameters during machining operation Through operational modal analysis. Int J of Mach Tools and Manu (49): 947–957.
[17] Turkes E, Orak S, Neseli S, Yaldiz S (2011) A new process damping model for chatter vibration. J Measu (44): 1342–1348.
[18] Hilborn RC (1983) Chaos and nonlinear dynamics. Oxford University Press, Oxford.
[19] Grassberger, P, Procaccia, I (1983) Characterization of strange attractors. Phys Rev Lett 50(5): 346-349.
[20] Kanz H, Schriber, T (1997) Nonlinear time series analysis. Cambridge University Press, Cambridge.
[21] Sharif Ullah AM, Harib HK (2010) Simulation of cutting force using non-stationary gaussian process. J Intell Manu 681-691.
[22] Schmitz TL (2008) Machining Dynamics. New York: Springer Science.
[23] Imani BM, Pour M, Ghoddosian A, Fallah M (2012) Improved dynamic simulation of end- millingprocess using time series analysis. J Scientia Iranica B 19(2): 294– 302.
[24] Pour M, Torabizadeh MA (2014) Improved prediction of stability lobes in milling process using time series analysis. J Intell Manu 27(3): 665-677.
)