@article { author = {Samadi, B. and Masoumi Dehaghi, I. and Ghaedali, H.}, title = {Investigation of sequence effect on welding residual stresses and distortion in a aluminum shell opening}, journal = {Journal of Solid and Fluid Mechanics}, volume = {8}, number = {3}, pages = {1-14}, year = {2018}, publisher = {Shahrood University of Technology}, issn = {2251-9475}, eissn = {2251-9483}, doi = {10.22044/jsfm.2018.6291.2483}, abstract = {In this research, opening welding on an aluminum shell and investigating the effect of welding sequence on residual stresses and distortion after welding by finite element simulation have been investigated. Then, the results are compared in ABAQUS and SYSWELD.Using experimental data, simulation and experimental results are compared. The temperature distribution is not uniform in different area of the welding zone, the most important factor in this incident is the non-uniform welding geometry. Thermal retransmission and the difference between thermal pick in different situations increases with increase of welding steps, which will affect the development of residual stresses as well as distortion after welding. The peak of the residual stresses is reduced and more uniform distribution occurs as the number of welding sequences increases.. The results show that the higher the distortion in the weld region (the elongation), the greater the amount of elongation. Also, the amount of elongation will be greater, with the higher the distortion in the weld area.}, keywords = {Welding sequence,Finite element,Residual stress,Distortion}, title_fa = {بررسی تاثیر ترتیب جوشکاری بر تنش‌های پسماند و اعوجاج جوشکاری گشودگی در یک پوسته آلومینیومی}, abstract_fa = {در این پژوهش، به بررسی جوشکاری گشودگی روی یک پوسته آلومینیومی و بررسی تاثیر ترتیب جوشکاری بر تنش‌های پسماند و اعوجاج بعد از جوشکاری به‌کمک شبیه‌سازی المان محدود در نرم افزار تحلیل‌گر آباکوس پرداخته شده و با شبیه‌سازی در نرم افزار سیسولد، نتایج این دو نرم‌افزار نیز مقایسه شده‌اند. همچنین با استفاده از داده‌های تجربی، به مقایسه نتایج شبیه سازی و آزمایش تجربی پرداخته شده است. نتایج نشان داده است که توزیع دمایی در نقاط مختلف مسیرجوشکاری یکنواخت نمی‌باشد که مهمترین عامل این رخداد، غیریکنواختی هندسه جوشکاری است. هرچه تعداد مراحل جوشکاری بیشتر شود، باز توسعه حرارتی و همچنین اختلاف بین پیک‌های حرارتی در موقعیت‌های مختلف بیشتر خواهد شد که این خود بر توسعه تنش‌های پسماند و همچنین اعوجاج بعد از جوشکاری اثر گذار خواهد بود. نتایج بررسی تنش‌های پسماند حاکی از آن است که هرچه تعداد ترتیب‌های جوشکاری بیشتر شود، پیک تنش‌های پسماند کاهش پیدا می کند و توزیع یکنواخت‌تری در تنش‌ها ایجاد می شود. موضوع حائز اهمیت در اعوجاج ایجاد شده در این سازه، میزان کشیدگی به داخل و همچنین تغییر مکان و تغییرشکل مسیرجوشکاری است. نتایج نشان می‌دهد که هرچه میزان اعوجاج در ناحیه جوش ( کشیدگی به بیرون) بیشتر باشد به همان نسبت میزان کشیدگی به داخل بیشتر خواهد بود.}, keywords_fa = {ترتیب جوشکاری,المان محدود,تنش پسماند,اعوجاج}, url = {https://jsfm.shahroodut.ac.ir/article_1320.html}, eprint = {https://jsfm.shahroodut.ac.ir/article_1320_f49b441e88c5a07024d0a3229cd60a9c.pdf} }